An Electronics Voyage – 50 Years of Marine Electronics

An Electronics Voyage

Sail through a half-century of innovation.

Our 50-year marine electronics journey begins in 1971 aboard our Chris-Craft Commander 35 Salon powerboat. Our vessel is magical and, as time passes, our electronics array transforms. Day by day, we aren’t aware of the improvements; however, friends that climb aboard once a decade say, “The years tell of sweeping electronics changes the days cannot.”

Our helm in 1971 is fitted with the best electronics available—a Simpson crystal VHF-FM radio with 12 channels, a Furuno marine radar system, a Lowrance sounder/flasher, and a Ray Jefferson Loran-A unit. As our vessel moves through the years, the equipment that comes on board isn’t necessarily the first of its kind, or the best, but simply representative
of the tremendous improvements made over a half-century. 

So we press onward. As we move into the mid-1970s, Loran-A is replaced by SI-TEX 777 Automatic Loran-C, which is a more stable system and easier to use. Furuno introduces an Ultra-Compact Radar in 1976, and in 1979, we have a Lowrance LDD-1800 digital depth sounder. 

As we venture into 1980, our Alden Marinefax Weather Chart Recorder gathers data from multiple sources and provides a more reliable forecast for trip planning, while our SMR 7800-X VHF marine radio is watertight, will remain corrosion-free, and can be set to constantly monitor five of 78 VHF channels.

Finding the bottom just got a little easier in 1982, with the introduction of the Lowrance X-15 sounder. We also locate a NARCO EPIRB (emergency position-indicating radio beacon) on board, first invented in World War II to find downed fighter pilots but updated in the late 1980s for the average mariner to use. 

Our boat cruises along using an Autohelm Autopilot, and in 1988, the Trimble 4000SLD GPS receiver comes out using U.S. satellites to pinpoint your exact latitude-longitude, with an error built in called standard deviation. GPS is very expensive, but we see how it aids mariners and is a game-changing nav tool. We also like our Datamarine Link 8000 display that provides wind, depth, and speed information on a single interface.

Our vessel crosses into the 1990s, and now we can plug in a regular household 120-volt appliance into a 2,000-watt Xantrex inverter. Voila! We can make coffee just like at home, and even a slice of toast. 

In 1990, Garmin introduces the GPS 100, one of the first marine GPS units, and follows with the GPSMAP 185 in 1999, one of the first chartplotter/sonar combo units. In 1996, the MariStar-M satcom from Scientific-Atlanta offers two-way voice, fax, and data satellite communications, so we can call or fax from anywhere.

Everything is getting smaller and more powerful, like our Uniden HH980 Handheld VHF radio, which is also watertight. In 1998, the Motorola Iridium Satellite telephone arrives, promising the ability to call from anywhere on the planet. Iridium works, too, though it is short-lived. However, with all these new gadgets, how can we connect them all so viewing the data is easier?

NMEA 2000 protocol finds its way into the marine landscape, a plug-and-play communications standard used for connecting marine sensors and display units. Communication runs at 250 kilobits per second and allows any sensor to talk to any display unit or other device compatible with NMEA 2000 protocols. The stage is set for our autopilot, wind instruments, depth sounders, navigation instruments, engine instruments, and nautical chartplotters to all connect and be displayed on a single screen.

However, in 2001, Furuno’s NAVNet offers color radar, chartplotting with C-Map NT, Navionics or Furuno cards, 600W fish finder, and 12-channel GPS receiver on a 10.4-inch LCD color display. It’s a powerful bundle for the captain.

In 2004, the Raymarine C Series Multifunction Displays are introduced, and later in the decade, a slew of other MFDs come onto the market. It’s a game changer made possible by NMEA 2000, as data that was once scattershot is all collected in one place for the captain. 

Chartplotters and cartography are also becoming much better as we motor through the early and mid-2000s. We’re constantly updating our C-Map cards to get the latest maps for the water we are visiting, but it’s a must-have because we’re seeing how paper charts could become a thing of the past, to have and to hold but never actually look at again.

Our sonar becomes more powerful in 2006, as Furuno’s Searchlight Sonar can reach 5,000 feet, while Simrad’s SL30 and Wesmar’s Focused Beam reach more than 3,000 feet. Our powerful laptop is now a chartplotter, and with Maptech’s U.S. Boating Charts DVD, we can view all of NOAA’s electronic charts on a disc.

As the 2010s roll around, our vessel now looks very modern: MFDs, small VHF units with handhelds to complement the base unit, satellite TV to watch our favorite shows, and Sirius radio and weather. Our MFDs in the mid-2010s are getting bigger and with touchscreen displays, our MFD becomes the ultimate “pinch-swipe-zoom” toy. Only those still using a flip-phone are unaware of the technology.

We can also now monitor our boat from afar, and in 2011, we are using Siren Marine’s tracking systems called Pixie and Sprite, with text messages sent to our phones informing us  of any change to our vessel’s state or position. 

Also in 2011, SI-TEX introduces its AIS products including the MDA-1 Metadata Class B Transceiver, and our first glass helm from Garmin, the GPSMAP 8000 series, is installed in 2013.

Even the bottom of the boat is transformed, as our underwater lights illuminate the sea, while inside LEDs offer more lumens on far less power. Digital switching from C-ZONE is making the connection and power supply for our electronics even easier and more secure.

Today, autopilot is more dependable than ever with our Garmin GHP Reactor system, and our boat can now dock itself as the propellers twist and turn. We also saw our smoky generator replaced by Lithium Iron Phosphate (LiFePO4, LFE) batteries and a Xantrex Freedom XC 3000 PRO Marine inverter to supply all the AC power we need while on the hook.

Space and weight have always been limiting factors with electronics and because everything is smaller and lighter as we power through 2021, we are more electrified than ever. Fly Solartech solar panels are sewn into biminis. The apps on our smartphones allow for monitoring and controlling our boat from anywhere in the world. The Siren 3 Pro even lets us check engine data and remotely control lights, cabin air conditioning, and other systems with our handheld devices.

What is next? And how will our electronics array look after another 50 years? Only time will tell. 

— by Doug Thompson

Smart Boating

Smart Boating

Brunswick Corporation is the Godfather of smart boating.

Back in 2008, Brunswick Corporation introduced the world’s first fully intuitive joystick piloting system with MerCruiser’s Axius and Zeus systems. It set new standards for power and performance in marine propulsion.

The company knocked down its last bowling pin in 2014 and started expanding its marine business in earnest. The acquisition of Power Products-Global Marine & Mobile in 2018  took Brunswick to the next level, not only to provide more options for the boat owner but also to create technology that can control a boat’s electronic, electrical and power
systems with a touch of a button.

Integration Nation

“Systems integration is critical to the boating experience,” says Lee Gordon, Brunswick’s director of marine communications and public relations. “We have four distinct pillars to our Parts and Accessories division strategy—Mercury engines, electrical systems, and integration services with Power Products and all of its brands, Attwood and the more than
four million parts on boats, and our distribution channels with Land ‘N’ Sea, Kellogg and Seachoice, among others. With all of this connectivity, Brunswick is able to offer the boater a range of products and services that others can’t offer.”

Mercury Marine demonstrated the integration technology during their Lake X event and at the Miami International Boat Show on a Harris 250 Grand Mariner pontoon boat. Mercury outboards and Fell Marine’s wireless man overboard (MOB) system were all controlled by Power Products’ CZone Digital Switching system…through a display, a fob or a  smartphone. Automobiles have keyfobs that unlock the car, set up the seats, radio, and heating or air conditioning controls.

Fob for MOB

The same now happens with your boat. CZone’s wireless keyfob can turn on the batteries, the lights and start up the pumps. The system has mode settings, so before you even
step on board, the boat can fire up the generator, the watermaker, the air conditioning, and the helm instruments so they’re ready to go. No more hopping aboard and spending time turning on the various switches and controls required to leave the dock or tuck it away for the night. Now THAT is smart boating.

Fell Marine also has a fob that connects to the CZone and Mercury’s Smartcraft network and can clip to a lifejacket or be worn on a wristband or as a necklace. Through a hub that attaches under the dash that connects with the boat’s gauges and instruments via the NMEA 2000 busbar, if a passenger falls overboard and the fob is under water or more than 50 feet from the boat, the engines will immediately stop. This gives time to locate the person. After six seconds, the engines are able to restart in order to retrieve the victim.

“The integration level with Smartcraft allows us to be a little smarter because we now know the state of the engine,” says Daniel Clarkson, general manager of Power Products Integrated Solutions. “We don’t have to trigger an emergency stop or SOS if the boat is sitting still and the engines are not running and not in gear. Based on that data we see on the Smartcraft bus, we can now smartly decide if we want to initiate a MOB.”

The alarm setup on the pontoon was based on the engines and whether they were running and in gear or not in gear. If the engines were running in neutral and someone went back and dropped the swim ladder, an alarm would go off. The system is configurable for any desired setup. In addition, the Fell Marine MOB app can also control the systems, such as turning on the engines, controlling the lights, etc., through CZone, and whatever was adjusted would also appear on the helm display.

Coming to smart world near you

The FELL Marine/CZone integrated technology for smart boating is not yet commercially available, but the demonstration showed proof of concept and the power of integrating different technologies into a common system. “We are in the middle of a development program to offer the next generation MOB device that will be Smartcraft compatible and have features beyond MOB, including up to seven-passenger FOBs,” says Dave Maryanov, Power Products marketing manager. “They’ll also be able to notify an MOB event via AIS, EPIRB, VHF, and cell phone notification, identify the MOB location via dropping a pin on an MFD or cell phone, and have theft deterrent capability requiring passcode or FOB to start
the engine.” The projected release of the system is near the end of 2019.

“Add in Vessel View, Nautic-On and our other partners, and you have the ultimate systems integration, which allows boaters to have the same amenities that they have in their home or their car,” says Gordon. “Our ultimate goal is to elevate the entire experience. Providing innovation and inspiration out on the water will keep boaters engaged and happy, ultimately providing an experience that will make boating easier than ever before.”

By Steve Davis, Southern Boating April 2019

Flexible Displays are a Gamechanger

Flexible screens open a new world for electronic displays.

New technology doesn’t just appear. It takes years of research, testing, and development to bring ideas and inventions to the real world and even longer to the maritime market. A perfect example is the evolution of battery power. Electric propulsion has been around for a long time, but it took years of research and development to feasibly power electric automobiles and now, larger boats.

After years of testing, a new technological advancement makes its debut this year: flexible displays and sensors.

Like batteries making advancements on land-based products before taking hold in the maritime market, flexible displays and sensors are reaching consumers through cell phones and tablets, and the technology will undoubtedly make its way to the maritime industry.

Flexible Screens

A few companies have been developing flexible displays over the years, which use the Active-Matrix Organic Light- Emitting Diode (AMOLED) technology. In October 2018, Royole Corporation introduced the world’s first commercial foldable smartphone, FlexPai, which gives users a tablet-size screen that can fold to the size of a smartphone. The high-definition, ultra-thin screen can display as one image or as a split-screen that supports separate, simultaneous operations.

Samsung has been developing flexible display technology for about eight years and is set to release its Infinity Flex Display in 2019. It, too, allows a tablet-size screen to fold into the size of a smartphone, but with the use of two separate displays, a large display that unfolds on the inside and a smaller “cover display.” The Infinity Flex Display along with its new interface design, One UI, allows users to have a compact smartphone that unfolds to a larger, immersive display.

Whatever you’re doing on the smaller screen isn’t lost when opening to the larger screen as three active apps can work simultaneously. Technology group Heraeus in Germany also is working on foldable displays. They’ve created a hybrid material, Clevios HY E, that consists of conductive polymers and silver nanowires that can fold again and again without losing conductivity.

LG has its own flexible displays and plans to unveil their foldable phone this year as well, but the technology really showed when they introduced a 65-inch “rollable” ultra-high definition OLED display. And their latest 77-inch can “roll” into a circle about three feet in diameter. Imagine the room you’d save onboard in the side cabinet without a full, flatscreen TV to hide.

Speaking of which, how does this fit in with boating?

As mentioned, LG’s flexible TV, expected for release in the second half of this year, not only saves space but also offers a thin, ultra-high definition display that provides incredible picture quality and requires less power. For the helm, flexible displays can bend around the console as one screen. Finding its way to some automobiles, a transparent, augmented reality display could mold with the helm windows to show potential hazards and markers, such as Raymarine’s ClearCruise AR technology.

Rollable and foldable displays could unroll into an electronic chart for planning voyages and have routes and navigation warnings superimposed. For cruisers, foldable, portable displays can stay with the helmsman as they move around the yacht for a hands-on connection with navigation and automation controls, alarms, etc.

At the 2019 Consumer Electronics Show held January 8-11, Samsung showed its 6.1-inch AMOLED flexible display with a “hole punch camera” embedded into the screen that is expected to launch this spring, and Royole featured its 7.8-inch AMOLED screen that folds in half. LG’s 65-inch rollable TV was introduced and measures slightly longer than 60 inches within a stand that’s half that size, which also includes the sound system. Then there’s the smart mirror that not only reflects but also shows Google Assistant and streams YouTube videos right on the mirror.

Obviously, the flexible display technology will go through growing pains as consumers put the products through real-world testing, and it’ll probably take a couple of years to go through a few versions before the technology proves itself and the market embraces it. But with companies like Sony, Huawei, ZTE, and Lenovo also working with flexible displays, the technology is unfolding at a quick pace. For now, costs are high. Royole’s tablet phone is expected to retail at $1,300 and Samsung could be in the $1,700 range, but both will have 5G network capability and use the latest Qualcomm Snapdragon chips.

Stay tuned, because the latest concepts are well on their way to reality, and 2019 looks to be an exciting year for new electronics.

By Steve Davis, Southern Boating February 2019

Electronics Troubleshooting Tips

Save yourself a bundle with these electronics troubleshooting tips

As is the case with most boat gear failures, electronic equipment problems always seem to crop up at the worst possible time. The multi-function display bites the dust when heading out for a day of fishing or the depth sounder blanks out while transiting some remote location during your annual cruise. Tech support is a wonderful thing, but self-reliance and the ability to recognize and fix simple problems are even better. Here are a few basic electronics troubleshooting tips to help bring your ailing electronics back online as quickly as possible.

Knowledge is Power

The first step in troubleshooting the system or piece of electronics gear is something you should have already done before the problem even arose: read the owner’s manual. A basic understanding of how the gear or system functions and is installed before you start troubleshooting is extremely helpful. It will assist you in recognizing and locating common problems. Most manuals will also have a basic troubleshooting section that helps point you in the right direction.

Start with the Basics

When a piece of electronics gear fails to turn on, start by checking the power connection at the unit for looseness or corrosion. If your DC power panel has a voltmeter installed, take a quick look to verify that it shows the correct voltage and that all required breakers are turned on. You wouldn’t be the first to realize a problem was actually caused by a battery switch or circuit breaker being in the “off” position.

For electronics that work intermittently or lose certain functions, check the remaining plugs or wire connections. These could also suffer from corrosion or may have loosened over time due to vibration. As odd as it may sound, sometimes problems can be corrected by simply disconnecting cable plugs and plugging them back in. The same is true for inline cable connections, which can loosen due to excessive movement or vibration if not secured or mounted properly. Trace the cable runs to see if there are any problems (breaks, damage, etc).

Visibility

If a unit powers up but shows nothing on the display, start simple and check the display brightness and contrast settings. These settings often get adjusted on purpose (to preserve night vision, for example) or by accident to the point where the display is no longer visible under different lighting conditions.

Other control features can also generate what I like to call “operator induced anomalies.” If your radar fails to pick up targets, for example, verify you’re on the correct range setting and that the gain/sensitivity features are adjusted correctly.

Voltage Checks

When it comes to hardware problems, if you’ve verified all connections are tight and the problem still exists, it’s time to get all technical and break out the multimeter. Every boat should have one on board. You can buy a multimeter for as little as $6 at Harbor Freight. Stay away from pen lighttype voltage testers. They can tell you if there’s voltage, but not how much—a critical troubleshooting flaw as many electronics fail to operate if the voltage drops below a  certain point.

To check the power to a piece of gear, turn the unit off and disconnect the power plug or access the terminal strip where power is connected. Then verify that battery switches and breakers are in the “on” position. Set the multimeter to DC volts and measure the voltage by connecting the meter’s negative probe to the equipment plug’s negative lead and positive probe to the positive lead. If you accidentally reverse the probes, the meter will simply display a negative reading.

A voltage reading of “0” indicates no power is reaching the unit (tripped breaker, blown fuse, loose connection, broken wire, etc). An item of note: if a fuse that blows multiple times when replaced, that should be considered a symptom rather than the problem itself. A low voltage reading indicates low battery voltage or, possibly, additional resistance in the line such as a corroded or faulty connection. Verify that the correct amount of power is leaving the breaker panel and if so, work your way toward the equipment in an effort to identify the problem. If not, then verify battery voltage is correct and proceed from there.

Consistency is King

Another thing to consider is how steady or consistent the voltage is during equipment operation. Some electronics draw more power during certain operations, such as your VHF radio when transmitting versus receiving. While you may have a full 12 volts at the power plug when the radio is disconnected or simply turned on, that voltage can drop well below a usable level when the radio is keyed to transmit. This is often due to a weak battery or possibly a corroded connection. Monitor your DC panel voltmeter (or use your voltmeter) while keying the radio to see if the voltage drops.

NMEA 2000

While standalone electronics will have their own dedicated power plug or source, newer electronic systems will likely be powered by a NMEA 2000 (N2K) trunk or backbone. If the system is installed correctly and was working previously, and you confirmed that the voltage supply is correct and that all plugs and connections are good, then the problem could be with the backbone itself. There are meters that allow you to test N2K backbones, but they’re pricey ($600 plus) and more than most occasional users are willing to spend. If you think the problem lies with the backbone, it’s likely time to call in a professional.

By Frank Lanier, Southern Boating December 2018

Davit Maintenance

Keep your lift in tip-top shape with some davit maintenance

Davits work on boats without fanfare. Akin to heads and air conditioning, no one thinks about davits unless they break. But a davit with a hitch or one that won’t run at all is a major hassle that can ruin a weekend. It’s a sad sight to see a pair of personal watercraft or a tender stuck on a flybridge, high and dry, when there are islands to explore.

Boats larger than 60 feet often need a davit to deploy the tender—it’s often not a luxury but a necessity to get to shore. An 800-pound tender hanging at the end of a 10-foot davit boom is a big structural load vulnerable to forces of wind and sea. It’s easy to see why the routine davit maintenance is vitally important, and why it’s crucial to quickly transfer the tender from one place to another.

Over the past 20 years, hydraulic davits have become the standard on boats and displaced manual boom davits with electric winches. “The market is now hydraulic davits because it’s easier for the operator to use,” explains Garnett Byrd, president of MarQuipt, based in Pompano Beach, Florida. “Electronic drum winches are loud and subject to bird nesting where the cable wraps around on itself, while hydraulics are quiet, and the linear cable system keeps the cable from wrapping on a drum. You can add power rotation, and the boom can elevate and extend while the tender is in the air to increase flexibility and ease of use. All those features add up fast to make hydraulics preferable.”

Use it or Lose it

Exercising your davit offers a host of advantages and helps you notice a potential problem. Running it lubricates all the internal parts, including the valves, pistons, cylinders, and seals. The easiest davit maintenance? Run the davit weekly, or even monthly, to avoid problems well before they start. “Problems can arise from an incomplete freshwater wash down,” says Byrd. “Remember to rinse the inside of the davit and not just the outside of the davit. Shoot fresh water through the head of the davit when on an angle so it washes down the inside components (cable, pulley sheaves, fittings, hydraulic cylinder bodies, etc).”

Be careful not to overload the davit. Know its lifting weight capability and also the weight of the tender complete with engine, fuel, fresh water, battery, fire extinguisher, and options such as a trolling motor and outboard engine jack.

Exercising the davit also helps keep you trained and ready for proper operation. If the first time you use the davit to launch a tender is in a remote location, this is a recipe for disaster.  You can operate remote models with one hand, but it’s important to be comfortable with the operation before you attempt a lift.

The Issues

Davits may have by three types of problems: electrical, hydraulic and mechanical. How boat owners and operators address these problems depends upon the urgency of the situation. Is it something you discovered at the dock during downtime, or are you on a cruise and need to fix the problem to stay operational? “Electrical problems can often be the simplest things,” Byrd explains. “The first place to look is where you plug in your controller; check the male and female connection points.

This may be more troubleshooting than davit maintenance, but if one function gives you a problem, check the wires on the back and make sure they are connected and not broken. Spray corrosion inhibitor on the connections as a routine maintenance function to make sure that doesn’t become a problem.”

With hydraulic issues, air or debris that gets into the lines can hinder operation. “Hitching, balky or inconsistent movement may be a sign that air or debris has gotten into hydraulic oil,” says Byrd and adds that low hydraulic oil can contribute to these problems. “A little piece of debris in the system can intermittently prohibit the flow of oil to the valves. Maintain fluid levels by checking the hydraulic power unit and run the davit regularly.

The Solutions

If you have the skill, disassemble the valve and look inside for obstruction. Keep an eye out for leaks—obviously, any oil leak is a sign something is wrong.” Byrd suggests that boat owners can perform basic davit maintenance, such as the addition of hydraulic fluid, inspection of electrical connections and lifting cables for mechanical problems. But a qualified marine service yard should handle more advanced mechanical jobs such as the replacement of said cable or hydraulic lines and flushing and changing hydraulic oil.

As a final tip, when you rinse the outside of the davit, keep an eye for chipped or peeled paint. “Davits are typically painted aluminum, and we have isolation between dissimilar metals like stainless steel nuts, bolts and screws,” says Byrd. “If there are any paint scratches or chips, make sure you touch up those areas to avoid long-term paint oxidization.”

By Don Minikus, Southern Boating November 2018

Upgrade Your Electronics

Is it time to upgrade your electronics?

Cloudy display screens, buggy software, chipped or missing knobs—these are blatant signals that it’s time to upgrade your electronics. Some boat owners may live with broken equipment and just figure out a workaround. Think powering down and restarting your chart plotter when it gets “stuck”. These kinds of fixes only last so long.

Eventually, you upgrade your electronics and wonder why you procrastinated for so long. Not only are today’s hardware and software lightning fast, but they are often cheaper. Ever-faster electronics were predicted in the 1960s with Moore’s Law. (Computer processing power doubles every 18 months to two years.) Gordon Moore, one of the founders of Intel in the 1960s, came up with this “law”, but it’s more like two and a half to three years for future doubling. When you consider the possibility of artificial intelligence, you realize that supercomputers are only going to get more super.

Need to Know

For boat owners, knowing when to upgrade your electronics is based on both need and want according to Ron Muller, co-owner of Electronics Unlimited with Jim Bakatselos in Fort Lauderdale, Florida. “There are those tech guys that need to have the latest and greatest equipment,” explains Muller, whose team of employees take on refit and new installation electronics projects on boats ranging in size from small center consoles to megayachts.

“If you are one of those guys, I would say that would make it about every two years. We have seen some real changes in the way navigation is being integrated with multi-function displays (MFD); however, it’s not just regarding navigation. It’s also the ability to control other things on board with your MFD, such as the Seakeeper stabilizer system, underwater lighting and CZone digital switching, cell phone integration, and even flying drones.”

Screen Time

Often, the equipment just wears out. Poor screen visibility is common because of weather, age and outdated technology. “The biggest thing we see is customers living with old screens,” Muller says. “This would include displays losing brightness, the inability to interface with newer equipment, damaged screens due to salt and sun exposure, and the cost of upgrades, and there are carpentry costs to consider. Also, with most new equipment, you end up changing radar and sounder modules when you are changing brands so everything will match up and work well together.”

Processor speed and screen size is another huge issue boat owners must consider. The screens range in size from 7 inches up to 24 inches. “Just like computers at home, when you want to do stuff that involves video and multi-function displays, then things really slow down,” says Muller. “This is an area where, recently, manufacturers are making changes to the actual hardware they sell instead of just doing software enhancements, and it’s another reason to upgrade. The processor speed is most evident when running multiple sources on one display.”

Costs

Like anything else, the price is a big consideration when you upgrade your electronics. Balancing cost versus safety is something every boat owner must consider. “Determining what brand is the best these days is a real challenge, as there are similar features everyone offers and features that come with only that brand,” Muller says. “Consumers want to know if the new equipment will fit in the old hole in the dash, and can they use the old cabling, or do we need to pull new wires? When using a company like Electronics Unlimited, we can provide all those answers and if needed, schedule a boat visit and inspection of what is present and what new material is needed for the project.”

Computer-driven products are the items most commonly switched out and where you’ll get the most bang for your buck, notes Muller. “The biggest changes recently have been with radars, fish finders, and MFDs,” he says. “Radars are now digital and provide a much better picture. Sounders using CHIRP technology do the same for fishermen by showing more detail and also have improved interfacing capabilities with the MFDs—the best time to get a deal is during the summer months. This is our slowest time. Most of the yacht refits happen from October through April.”

For boat owners whose equipment is getting older—five years old or more—the time to upgrade your electronics is at hand. The features in today’s products are far better than in the past. There’s also been an improvement in performance in all areas of marine electronics, especially with Wi-Fi connectivity, and there are better satellite airtime usage rates.

Need for (processing) Speed

It’s not enough to just turn on your computer and tap into a signal. Today’s boat owners want powerful coverage for not only their laptops but also for their guests’ devices, including mobile phones and iPads. In addition, today’s Smart TVs need Wi-Fi to use streaming services like Netflix. “This is the area where we are seeing many changes—communications via satellite, Wi-Fi, and cellular networks,” says Muller. “This has been a costly expense and is still somewhat expensive, but the cost has been slowly coming down.”

By Doug Thompson, Southern Boating September 2018

Beyond Basic Safety Gear

Go beyond the basic safety gear. This is survival gear.

Safety on board is undoubtedly the most important aspect of boating. When something goes wrong, having the proper gear can keep you alive. Increase your chances of survival by going beyond basic safety gear.

Most boaters carry just the basics: navigational lights, air horn, PFDs, fire extinguisher, flare, and a bottle of water. But before you head offshore this summer, consider carrying an Emergency Position Indicating Radio Beacon (EPIRB), a personal locator beacon (PLB), emergency life raft, a night-vision camera, and high-powered spotlight.

I once was lost but now am found

An Emergency Position Indicating Radio Beacon (EPIRB) is essential when planning your safety gear.

The most recent European Union launch of Galileo navigation satellites added second-generation search-and-rescue (SAR) transponders to the International COSPASSARSAT Medium-Earth Orbit Search and Rescue (MEOSAR) constellation. The primary mission of the MEOSAR system is navigation. Its large footprint on the globe allows the use of Doppler measurements to calculate a distress beacon’s location, while the Low-Earth Orbit (LEOSAR) and Geostationary Orbit (GEOSAR) are primarily for gathering meteorological data. Both the LEOSAR and GEOSAR satellites, however, provide assistance when a distress beacon is activated. The MEOSAR array provides faster signal detection, greater reliability, and accuracy and will soon be the dominant system for COSPAS-SARSAT service.

This is the system that communicates with an EPIRB and PLB distress signal that transmits on the 406 MHz frequency. A GPS-enabled EPIRB can identify your location to as close as 164 feet. A PLB works the same way but only transmits about 24 hours (the EPIRB has a minimum 48-hour transmission) and is registered to a person whereas an EPIRB is registered to the watercraft.

There are a number of EPIRBs and PLBs on the market, such as ACR’s GlobalFIX V4 EPIRB which has an internal 66-channel GPS. It has a 406 MHz transmission to connect with the COSPAS-SARSAT system and also uses the 121.5 MHz signal for more accurate detection when rescuers are close by. McMurdo’s Smartfind G8 AIS (shown) is the first to combine 406 MHz transmissions with an AIS (Automatic Information System) locator. Ocean Signal’s rescueME EPIRB and Simrad’s EP70 are also highly rated.

 Was blind but now I see

Fishing in the Gulf at night won’t be fun if an oil rig gets in the way. Coming into the harbor isn’t any easier. With obstacles like tidal currents and other boats that can get in your path, docking can be a challenge. What if there was a man overboard scenario? Hope he’s wearing a PLB along with a strobe light.

Having a low-light and/or thermal camera that links with your electronic display is a godsend in those situations. Infrared or thermal imaging captures temperature differences between the background and the foreground. It detects thermal radiation that is emitted by anything with a temperature above zero. Thermal imaging cameras don’t need light to see.

A night vision camera requires some ambient light (from the shore or even the moon and stars). The latest technology has cameras capable of returning an image with just 0.1 lux (a full moon with a clear sky is 0.05 to 0.3 lux) and some with a sensitivity of 0.0008 lux. Resolution size is a critical number with thermal imaging and night vision cameras, but the camera’s sensitivity mode is important as well. The higher the number, the more you can see. High sensitivity modes make the camera more sensitive to pick up changes in temperature, which is important when trying to locate a crewmember in a man-overboard situation.

As with most safety gear, there are a number of companies producing thermal and night vision cameras, such as FLIR, Raymarine, and The Yacht Group.

That Saved a Wretch Like Me

One of the handiest safety accessories is the spotlight. Not much needs to be said as most people understand the advantages of having a flashlight when it’s dark. ACR, FLIR, and West Marine are just a few of the manufacturers who offer spotlight solutions. Fully automated systems with cameras, such as The Yacht Group’s Yacht Cam Bright that combines the night vision camera with a searchlight are extremely helpful.

The Yacht Group’s Yacht Cam Bright is a combination night vision camera and searchlight.

Its extreme lowlight sensitivity of 0.0013 lux (color) and 0.0008 lux (monochromatic) distinguishes images with 2.13-megapixel resolution and 30x optical zoom. The wide spot beam, effective to 1,000 feet by 70 feet, can further illuminate an object seen in the camera’s all-in-one unit with joystick control.

In addition to these important safety products, keep in mind the location in which you’ll be cruising. Conditions on the water can change rapidly, so logically consider all possible scenarios prior to heading to the marina. Think about how far you’ll be from shore, the water temperature will be, and weather conditions. Make sure to have ample supplies of food and water in the event you’re out longer than anticipated. Even a ditch kit if you have to abandon ship. When it comes to boating, safety is always the first priority.

Useful Resources

ACR

FLIR

OCEAN SIGNAL

MCMURDO

RAYMARINE

SIMRAD

THE YACHT GROUP

WEST MARINE

By Steve Davis, Southern Boating June 2018

Boating with Drones

Drones add a unique tool to the boating lifestyle.

Raymarine released a new app that attracts anglers and photographers alike—the Axiom integration for unmanned aerial vehicles (UAV), or drones. The UAV app runs in the new LightHouse 3 operating software through the Axiom or Axiom Pro multifunction navigation display just as the radar, sonar and chart plotter apps operate.

The interface is a preconfigured split screen—on one side the nautical chart and on the other, a live video display from the drone. The map side shows the position of the boat along with its course, speed, heading, depth, and all the features you’d normally see on an electronic chart.

As soon as the UAV leaves the deck, the chart shows the drone’s position and its relation to the boat. A “rubber band” line on the chart connects the drone icon with the boat icon, so even if it’s flown far away or beyond the range of the chart on the display, a simple zoom adjust reveals its position. In turn, the drone icon communicates its direction, speed, height, and which way the camera is pointing. The camera display side of the screen provides real-time video from the drone’s camera.

Fun and Fishing

Jim McGowan of FLIR Maritime/Raymarine says that many boaters use drones for fun when fishing or cruising but that operating them from a boat can be challenging. Consequently, FLIR Maritime/Raymarine looks for ways to make the technology and process easier with automation.

Parent company FLIR Systems has a technical partnership in place with UAV manufacturer Dà-Jiang Innovations (DJI) to make a line of airborne thermal cameras to attach to larger DJI drones. The DJI Zenmuse XT2, for example, pairs with FLIR’s Tau2 thermal sensor and 4K visual camera for commercial applications to inspect power lines, pipelines, and solar panel grids. The system is becoming more prevalent with law enforcement as well as the U.S. Coast Guard and search-and-rescue operations. FLIR and Raymarine’s engineers discussed how those systems could apply to the maritime industry which led to the UAV integration, but McGowan adds, “There were a lot of unique things we had to do to make it work well in the maritime environment.”

Competitive fishing tournaments, in particular, are where they’ve focused efforts to make drone operation more automated due to most tournaments’ catch-and-release rules. “They have to have photographic evidence of their catch and the gear they were using, so the drone is another tool in their toolbox for capturing whatever photo or video they need,” says McGowan and adds that video of the big catch provides a unique perspective.

“That’s where a lot of the automation work we’re doing comes in. You can launch a drone and fly it and orbit it, but a lot of time you’re short-handed, especially when you get a big fish on the line and everyone’s running around like crazy trying to help, and the last thing [you want] is to have someone flying the drone to keep the action in frame.” Raymarine is trying to automate that process according to McGowan. “You can hit a button and get the drone in the air. The drone knows where the boat is, the drone knows where to point the camera and tend to itself to get the footage you’re looking for.”

Safe Return

For anyone who’s flown a drone, one advantageous feature is Return to Home (RTH). On land, the drone establishes its starting point and when the battery runs low or it goes out of sight, the RTH feature brings the drone back to its starting location automatically. But that becomes harder on a boat. “One of the big challenges is getting the drone back on board because the ‘home’ is moving,” says McGowan. Addressing that problem, Raymarine is in the process of developing the UAV integration with a two-way data link. “The drone sends its telemetry back to the boat and the boat sends data back to the drone so the drone knows where the boat is and where to return to,” explains McGowan.

“It knows the safety parameters around the boat’s environment, so if you have masts and outriggers and antennas and fishing tackle up in the air, the drone knows what the safe sphere is around the boat and how close it can approach. The way it’s going to work in this first cut [of the software] is when the drone returns to the boat, it will basically hit the edge of that safe envelope and hover and wait for you to recover it.” At that point, the operator takes over via the controller. The motion of the vessel can make the recovery dramatic, especially with smaller drones, so unless you have a boat with a big foredeck or sunpads, catching it out of the air is probably the most efficient method right now. Phase two of the software hopes to include ways to improve that recovery process.

Besides tournament fishing, practical advantages of having a drone are finding schools of fish or looking out for reefs and shoals. Imagine cruising in The Bahamas, where the bottom changes rapidly, scouting out an anchorage to get a feel for what the conditions are going to be like. The number of possibilities where drones and the UAV app can aid in the maritime environment are seemingly endless.

By Steve Davis, Southern Boating July 2018

FUSION Entertainment Debuts New Audio Equipment

FUSION Entertainment debuts their top-of-the-line series that takes audio entertainment to the next level.

When it comes to the knowledge spectrum of technology as it pertains to music sound systems, I’m closer to the technophobe than the technogeek end of the continuum. I know the difference between bass and treble, and I can tell when the volume level distorts the quality. That being said, I do love blasting high-energy music—think ZZ Top or Aerosmith—right before it reaches that level. So, when I was invited to experience FUSION Entertainment’s newest product line a couple of days before Star Wars Day—May the 4th be with you—I couldn’t resist sharing my Pandora playlist. I gotta say, cruising on a Jupiter with the Star Wars theme song cranked up and absolutely no distortion was simply stellar.

Based in New Zealand, FUSION Entertainment entered the marine market more than a decade ago. Garmin bought FUSION four years ago, and the electronics powerhouse significantly invested in their technology resources. Since then, the size of their engineering team has more than doubled. The debut of the Apollo Series marine audio entertainment system is evidence that the investment has paid off not only for the company but especially for boaters who love music.

Meet Apollo

The Apollo Series—named for the NASA space program’s advanced technology that landed humans on the moon as well as the Greek god of music—sets a new standard in the industry according to Chris Baird, managing director of FUSION Entertainment. “For many years, our head units have defined marine audio entertainment. While there has always been an ability to add features, no one has created a paradigm shift in this space, until now. After listening to our customers and closely examining trends and innovations in other industries like touchscreen and glass helm systems, we knew it was time to change everything.” The first two Apollo products—the RA770 and SRX400—do, indeed, exhibit that change in many different ways.

Design and functionality

The flagship FUSION RA770 (4.3-inch display) is designed specifically for the marine environment. It includes a one-piece glass touchscreen display, built-in Wi-Fi streaming, Digital Signal Processing Technology (DSP) and PartyBus capabilities. The full-color LCD display and one-piece glass touchscreen eliminates searching for the appropriate button on a bumpy boat. Instead, users just use the finger motions they already use on their phones. Tap the screen to start the music or pause, swipe right or left to forward through a playlist or to repeat a favorite song. The display blends perfectly with modern glass helms and is an attractive addition to any steering station. The FUSION Apollo Series SRX400 (2.7-inch display) offers a more compact product for smaller vessels that includes Wi-Fi streaming, DSP, and PartyBus functionality.

Sound quality

Users will notice a difference in the sound quality of the Apollo Series as compared with competitors’ products. FUSION DSP provides optimized audio delivery to all speakers on board in any environment. FUSION goes a step further and provides an easy-to-use FUSION-Link app to set up users’ DSP profiles. The process is simple, quick and involves relatively few steps. The end result is supreme audio quality at every volume level. Whether you want to crank out some heavy metal or enjoy soothing symphonic melodies as background music, you’ll be satisfied. The FUSION-Link app also enables users to download software updates right from their phone—no awkward and time-consuming procedures required.

Music choice

FUSION’S PartyBus lets users choose the music on the entire boat or in a specified location on the boat, such as a cabin or stateroom. Users can add additional PartyBus-enabled stereos to their onboard entertainment system. This provides the option to join Party Mode and play the same perfectly synched audio source through the entire vessel. Personal Mode enables other available audio sources from the stereo in their zone without disrupting Party Mode in other areas. The Apollo RA770 offers users a number of audio soundtrack source options. That includes Bluetooth, Optical Audio (TV), Advanced SiriusXM features (USA only), DAB+ ready (available in Europe and Australia only), AM/FM radio, AUX, and USB. Stream music from a mobile device via Universal Plug and Play (UPnP). With built-in Wi-Fi, the Apollo series wirelessly connects multiple Apollo stereos without cables.

Additional features

If correctly installed, the FUSION Apollo RA770 and SRX400 are IPx7 are rated for dust and water protection. It also includes an internal Class-D amplifier. The RA770 includes two RCA auxiliary inputs, one SPDIF port for TV audio output, one Ethernet port, one USB 2.0 port for phone charging and media playback, one SiriusXM port, one Motorola antenna connector port, and is DAB+ ready. The SRX400 has one Ethernet port and one Motorola antenna connector port. Both models offer multi-language support and settings for English, French, German, Spanish, Dutch, and Italian.

You’ll see FUSION Apollo Series products on a number of models from boat builders. Those builders include Bavaria, Boston Whaler, Grady-White, Regal, and all Sea Ray production models. Stay tuned for additional product developments in the Apollo Series including speakers and amplifiers planned for a 2019 release.

fusionentertainment.com

By Liz Pasch, Southern Boating August 2018

Onboard Necessities

There are some items you just NEED to have onboard.

Some are for your safety, while others are for your sanity. Whatever the case, they are your onboard necessities.

To keep the boat sand-free:

Ventolation flip-flops and sandals may be the perfect beach and boat footwear. Keep your boat sand-free with these shoes.

 The rotary ventilated shoe enables sand, water, and air to pass through and not build up under the foot. The insole is positioned onto columns which act to rapidly expel sand and water but also allow your feet to effectively stand on air.

MSRP $34.99; ventolation.com 

To comply with regulations:

Your kayak, paddleboard or small RIB will comply with night navigation light requirements with Railblaza Nabipack Kit or Visibility Kit.

Each includes a three-foot, three-piece pole and 360-degree white light. The Visibility Kit also includes a red day flag, and the NaviPack has a red/green bow light and mounting options.

Visibility Kit II MSRP $94.99 or
NaviPack MSRP $179.99; railblaza.com

To keep your galley organized:

Save precious space in the galley with this nesting cookware set.

Made of 18-10 marine-grade stainless steel, Magma’s 10-Piece Nesting Cookware Set is now available with a cobalt blue finish exterior.

The Ceramica non-stick coating is non-toxic, PFOA- and PTFE-free and will not stain, peel, blister, or flake. Able to store in less than a half cubic foot of space, the set is scratch resistant, durable, and oven-safe to 500 degrees. Not for use on induction stovetops.

MSRP $319.98; magmaproducts.com

To entertain the kids:

Great for when you’re at anchor and need a break– just bust out this game to keep the kids occupied for hours.

The year is 1667 and you are a pirate sailing the waters of the Caribbean. A Spanish galleon floats nearby, and you’ve talked your crewmates into stealing all of its treasure, but who can you trust? To whom are you loyal? Tortuga 1667 is a pirate game of mutiny, plunder and deceit for two to nine players ages 12 and up.

MSRP $24.99; facadegames.com

To stay connected:

If you need to Netflix and chill or just work remotely, KVH has you covered.

The KVH Tracphone LTE-1 marine communications system uses cellular technology from two carriers that automatically switches between them for seamless coverage. Stay connected more than 20 miles offshore with up to 100 Mbps data speed in a compact, affordable design.

MSRP $1,699; kvh.com/LTE

 

 

Stay Connected: new products keep you connected

Electronics keep cruisers connected. Stay connected while cruising

Boat Shows provide a phenomenal opportunity to learn about and shop for new electronic products, if you need to replace them. Pay attention to a few that that will help you get internet and stay connected while cruising.

ICOM

Communications solutions provider Icom presented its new fixed-mount compact transceiver designed for tight spaces that packs a punch. The M330 series offers the same great performance as their M324 series. The waterproof transceiver includes an exclusive AquaQuake draining elemen, and built-in GPS. The M330 series’ small size is ideal for smaller boats that have limited space for mounting electronics.

Icom also debuted the M85, the smallest, lightest handheld radio available. The M85 has VHF marine channels and also 100 programmable land mobile channels, making it ideal for both marine and land use. The practical marine/land mobile radio combo is built to MIL-STD 810, with an IP67 waterproof rating, which protects the radio even if it’s submerged. This new commercial-grade marine radio is fitting for both recreational and commercial marine operations and features a built-in voice scrambler for private communications. The M85 also includes features for emergency situations such as MOB Alarm, Man Down and lone worker functions.

Icom began as an engineering and manufacturing company, making advanced, compact, solid-state radio equipment for use by amateur (ham) radio enthusiasts. Boaters will be happy know that they can stay connected while cruising with Icom.  Icom has since grown to become an industry leader with a product line that includes state-of-the-art communications equipment for marine, land mobile and avionics. icomamerica.com

WAVE WIFI

There’s a lot to be said for unplugging completely from the outside world, and it’s easier when you’re boating in areas where WiFi coverage is spotty, inconsistent or absent. But for some, staying connected isn’t just preferable, it’s necessary. Wave WiFi provides mariners, RV enthusiasts and marinas with advanced technology that simplifies the process of connecting to WiFi, and their new 3G and 4G cellular products work in conjunction with their WiFi antennas, routers, and proprietary web-based firmware.

Wave WiFi products offer outstanding performance because of the proprietary firmware technology embedded in each unit. The browser-based interface allows users to easily identify and connect to WiFi hotspots based on frequency, signal strength, encryption, and availability. At the same time, the Wave WiFi hardware and antenna solutions transmit and receive signals with the best possible clarity. This means that users can access connections with faster Internet speeds and remain connected to WiFi farther from the source.

The next generation of Wave WiFi products goes one step further and allows the user to connect to 3G and 4G cellular when WiFi signals are not available. The new Tidal Wave from Wave WiFi provides high-powered, dual-band WiFi plus 3G/4G and allows for concurrent listening across 2.4GHz and 5.1-5.8GHz WiFi channels along with SIMactivated cellular data. The Tidal Wave comes equipped with a gigabit port to support the fastest connection speeds. It includes high gain antennas to seek the farthest-reaching connections attainable. There is no software to download or install and, instead, uses a simple plug-and-play integration. The unit is also equipped for power over Ethernet (POE) for easy installation. The Tidal Wave will let you enjoy the luxury of WiFi, and/or cellular internet at the marina, on the hook and in many remote areas– the best way to stay connected while cruising. wavewifi.com

MAZU

 Winner of a Pittman Award and a Newport (Boat Show) For New Products Award, the feature-packed mazu mSeries provides reliable, worldwide service with the up-to-date weather, email, SMS texting, position reporting, charts and onscreen tracking, real-time NMEA navigation, and optional remote boat monitoring and control.

Represented by Ocean Marketing, the award-winning mazu mSeries hardware, when paired with the mazu iPad app, is the ultimate tool for cruisers and anglers to stay connected while on the water anywhere in the world. For anglers, mazu Sport Fishing features satellite images of sea surface temperature, chlorophyll charts, position reports, and SMS chat.

The mazu iPad app provides global coverage with an easy to use interface when paired with mSeries hardware. Access is free via an Internet or cellular connection. The smart antenna is easy to install, draws low power, and comes with 12 or 24-volt mSeries hardware. The antenna that doesn’t need to be mounted high. Affordable and flexible monthly service plans are available, including a drydock plan to maintain an account when a satellite connection isn’t needed. mazu-marine.com

By L.N. Evans, Southern Boating May 2018

Scandvik Lighting’s Surface Mount Dome Lights

Scandvik Lighting’s Surface Mount Dome Lights provide consistent natural white light without hotspots or glare. The high-power LEDs have a three-stage dimming touch switch, are dust-tight and rated for water immersion.

MSRP $72 (rectangular) and $81 (round)

scandvik.com

 

Other Uses for Radar

For cruisers, this radar is more than just a convenience. There are other uses for radar that can be lifesavers.

Think of radar as a sonar fish-finder, except the transducer/antenna is spinning inside the radome—that round covering on top of your boat. By transmitting thousands of harmless microwave pulses per second, the radar determines what objects are around you and
references their position to your bow.

Invented in the early 20th century, radar is now a common accessory on boats and costs have come down. However, there are many other uses for radar that are underutilized, as many owners don’t know how to get the full value of their units aside from the safety aspect. “Most boat owners today use their radar systems as a tool for collision avoidance,” says Jim McGowan, Americas marketing manager of FLIR Maritime and Raymarine. “Typically, that means nighttime, in the rain or in the fog. If you’re out after dark or in the fog, it’s very comforting to know that you have the radar on board if you need it in those circumstances.”

Other popular uses for radar include finding seabirds that feed on small bait fish. This is a specialized usage of the technology, but many anglers find success with it. By locating
the birds at long range, it gets them on the fish sooner with less fuel burn.

“My favorite radar feature that most boat owners don’t use is the radar offset feature,” McGowan says. “This allows you to pull the center of the radar sweep, where your boat is, either one-third or two-thirds of the diameter of the screen downwards. The benefit is it gives you more lookahead visibility without having to change the radar’s range scale or making the target display smaller.” Radar offset is important because most of the time you’re going to be moving ahead at speed. It’s convenient to be able to see farther ahead on the radar scope, sacrificing some range to the rear.

There are many uses for radar.

Some other uses for radar include keeping tabs on what’s in your way is enhanced with MARPA (mini automatic radar plotting aid) and ARPA (automatic radar plotting aid). There are collision avoidance tools built into the radar system that enable it to track targets on the scope, calculate their course and speed and advise you of potential collisions. MARPA-equipped radars require you to manually select a target and enter it into tracking mode. ARPA-equipped radars can automatically acquire new targets that enter safety or guard zones you specify.

“Regardless of how the target is acquired, once the radar has it in track, it will determine its course and speed and display it on the scope,” explains McGowan. “Targets that
are going to pass inside of your pre-defined safety circle will be highlighted with flashing symbology and an audible alarm. It’s a great feature to use in crowded waters or if
you’re out in open water and want to keep watch of distant vessels on the horizon.”

One of the biggest improvements to radar in recent times is the addition of Digital Signal Processing (DSP). Older generations of radars used analog filters to clean up unwanted
noise and clutter. They worked okay but needed lots of manual tuning and tweaking as conditions changed. DSP radars use a computer and custom software to analyze the signals. “The radar is now intelligent and knows what rain looks like, what boats look like, what birds look like, etc.,” says McGowan. “We can teach the radar to show the things we want to see and hide the clutter, all without manual tuning and tweaking.”

McGowan highlights the importance of wireless technology. “Raymarine’s latest generation Quantum radars have Wi-Fi connectivity to link them to the boat’s multifunction displays. This eliminates the heavy and expensive inter-unit data cable while maintaining a link that is reliable and secure. Installation is simplified, and the overall cost of the system is reduced, which is a win for boat owners.” Raymarine has added several new features and technologies to its radar line in the last year. Its newest innovation is the Quantum 2 CHIRP radar complete with more uses for radar, like Doppler Target Tracking. Doppler radar makes it even easier to interpret the radar display and determine at a glance which targets are headed toward you and which are moving away. Doppler radar can specifically determine which targets are moving and which are stationary, and then color-code them for easy identification. Red targets, for example, are ones to watch as they are closing in range.

Another addition to many Raymarine systems is ARPA radar tracking. Raymarine has offered MARPA on all its radar systems for many years; offering ARPA brings its radar platform to an even higher level, automating the target acquisition and tracking process. You can draw up to two safety zones on the radar scope. They can be a simple radius
or a sector of the scope. Any radar targets that enter that zone will automatically acquire and track it with no manual intervention required.

Radar technology is a great tool for collision avoidance, coastal navigation, bird detection, and much more—but practice is essential. “One thing I always encourage customers to do is to use their radar on bright, sunny days,” says McGowan. “Don’t wait until it’s dark or the weather turns bad. That is exactly the time when you want to be able to use the tool with confidence. By using radar on nice days, you’ll learn how it works, how it reacts, and you’ll be able to compare radar contacts to visible contacts you can see with your eye. Use these opportunities to practice with the ARPA and MARPA. Try changing modes,
adjusting settings, and see what happens.” You know what they say: Practice makes perfect. When it comes to radar, practice makes you confident.

raymarine.com

By Don Minikus, Southern Boating March 2018

Wondering how to make your boat wireless?

If you’ve ever wondered how to make your boat wireless, wonder no more.

You CAN cut the cords: Wireless control and monitoring are available with Power-Pole’s all-in-one marine tablet.

Remember when wireless technology was unproven, unreliable and untrustworthy? That was a long time ago and now, wireless is the only way to go. When Bluetooth came along, we embraced its one-to-one connectivity, and it’s become one of the most important tools on land and sea.

As technology has evolved, that one-to-one connectivity has now become too limited and boat owners want more. The C-Monster 2.0 wireless protocol developed by JL Marine, the parent company of Power-Pole brand products, offers wireless multi-point connections and display with its VISION tablet.

“We developed our own wireless communication with a different frequency,” says Curt Hill, advertising manager for Power-Pole, based in Tampa, where all the research, development and production takes place. “The reason we did that is the Bluetooth is a one-to-one connection, and while Wi-Fi has multi-point connectivity, it’s not strong enough to go through wet aluminum decks.”

Innovation Winner

The VISION tablet measures seven inches wide, runs on the Android platform for full web access and is NMEA 2000 capable. It is powered by the boat’s 12-volt cranking battery and has a line-of-sight range of up to 100 meters. That means the signal strength is 10 times stronger than Wi-Fi and does not require a router.

The tablet is one of two new products introduced by Power-Pole last fall. The other is the CHARGE Marine Power Station that won a 2017 IBEX Innovation Award. It’s an AC/DC and bi-directional DC/DC all-in-one marine battery management and charger system.

Captains can customize the C-Monster app to wirelessly control all connected accessories, such as trim tabs, the jack plate, bilge pump, livewell, lights, and sound. In addition,
all Android apps, such as fishing and navigation apps, can run through the VISION tablet as well as apps from Navionics and Mercury’s SmartCraft app. “My idea for the future of
our product is going to be on larger boats and yachts,” explains Hill. “Instead of thousands of feet of wire running throughout the yacht, you can put these control modules all over the boat and control different things with a tablet. This product is going to work at the OEM level and for re-wire projects.”

The tablet controls the whole boat, so you can ditch the wires.

Power-Pole first developed the product for its anchor line. The Power-Pole shallow water anchors allow anglers to stop and hold their boat quickly with the touch of a button. Company founder John Oliverio and the JL Marine engineering team first started working on the C-Monster protocol five-plus years ago to control the Power-Pole anchors, and now the 2.0 version is offering many more applications, including the VISION tablet.

“For a re-wire project, it’s going to save a lot of time and effort and has other benefits,” Hill adds. “If you have a big fishing boat, then you have livewells that you want to re-circulate all the time. But having them on full power kills your 12-volt battery too fast. Our product offers a dimmer switch, so you can dim down the livewell variably and save power.”

Feature Rich

The high bright screen on the VISION tablet is easy to see in full sun from any angle, even when wearing polarized sunglasses. The unit features daylight and nighttime settings, and enhanced map viewing technology allows the user to clearly see maps and satellite imagery. The enhanced imagery will also allow the user to see how the shoreline differs from the grass line.

Another feature is the swipe-down Water Shade, which protects and locks the screen against water spray that might activate or change screen settings. This is helpful when running or in the rain. The VISION unit is water resistant, rated at IP67, has three mounting options (flush, gimbal, and ram), and the built-in camera allows hands-free photos of you holding that big catch.

“There are inputs and outputs,” Hill says. “The inputs read things like your fuel gauge and trim position, and you can show all that on the screen. You can set up as many screens as you want and just swipe to the next screen. All the pinch-and-swipe functions work the same way.”

To simplify tasks, the VISION offers a multi-function button to control a host of tasks at once. For example, you can set up a “Take Off” button that could stow your Power-Pole anchors, lower the engine trim and deploy the trim tabs to a predetermined setting so you are ready for a quick hole shot. “Most of today’s motors, trim tabs and jackplates already have the trim sensors built in,” Hill says. “All that is ready to rig up, and once you get it connected to the VISION, you are ready to go.”

The VISION system will retail for $1,595 when it goes on sale later this year, and that includes the VISION tablet and one six-bank control module. Additional control modules
will be available separately.

power-pole.com

By Doug Thompson, Southern Boating April 2018

Naked Flex Mount

Mount your electronic devices anywhere with SeaSucker Vacuum Mounts. Connected to a sturdy seven-inch flexible gooseneck arm, the nonmarking rubber mount is UV stabilized and can hold up to 120 pounds.

The Naked Flex Mount adapts to hold cell phones, tablets, and GoPro cameras.

The “naked” in Naked Flex Mount means that you don’t have to have a special bracket to fit your particular device.

MSRP $105;

seasucker.com

More Boating Accessories

Exit mobile version